eoffset_per_angle - Compute External Offset Per Angle
|
loadrt eoffset_per_angle [count=N|names=name1[,name2...]] |
An offset is computed (from one of several functions) based on an input angle in degrees. The angle could be a rotary coordinate value or a spindle angle.
The computed offset is represented as an s32 kcounts output pin that is a compatible input to external offset pins like axis.L.eoffset-counts where L is the coordinate letter. Scaling of the s32 kcounts is controlled by the input (k) -- its reciprocal value is presented on an output pin (kreciprocal) for connection to axis.L.eoffset-scale. The default value for k should be suitable for most uses.
The built-in functions use pins fmult and rfraction to control the output frequency (or number of polygon sides) and amplitude respectively. The rfraction pin controls the offset amplitude as a fraction of the radius-ref pin.
One of the four
built-in functions is specified by the fnum pin:
0: f0 inside polygon (requires fmult == nsides
>= 3)
1: f1 outside polygon (requires fmult == nsides
>= 3)
2: f2 sinusoid
3: f3 square wave
Unsupported fnum values default to use function f0.
NOTES:
radius-ref: The computed offsets are based on the radius-ref pin value. This pin may be set to a constant radius value or controlled by a user interface or by g code program (using M68 and a motion.analog-out-NN pin for instance).
Stopping: When the enable-in pin is deasserted, the offset is returned to zero respecting the allocated acceleration and velocity limits. The allocations for coordinate L are typically controlled by an ini file setting: [AXIS_L]OFFSET_AV_RATIO.
NOTES: If unsupported parameters are supplied to a function (for instance a polygon with fewer than three sides), the current offset will be returned to zero (respecting velocity and acceleration constraints). After correcting the offending parameter, the enable-in pin must be toggled to resume offset computations.
EXAMPLE: An example simulation configuration is provided at: configs/sim/axis/external_offsets/opa.ini. A simulated XZC machine uses the C coordinate angle to offset the transverse X coordinate according to the selected fnum function.
eoffset-per-angle.N (requires a floating-point thread)
eoffset-per-angle.N.active bit in (default: 0)
From: motion.eoffset-active
eoffset-per-angle.N.is-on bit in (default: 0)
From: halui.machine.is-on
eoffset-per-angle.N.enable-in bit in (default: 0)
Enable Input
eoffset-per-angle.N.radius-ref float in (default: 1)
Radius reference (see notes)
eoffset-per-angle.N.angle float in (default: 0)
Input angle (in degrees)
eoffset-per-angle.N.start-angle float in (default: 0)
Start angle (in degrees)
eoffset-per-angle.N.fnum s32 in (default: 0)
Function selector (default 0)
eoffset-per-angle.N.rfraction float in (default: 0.1)
Offset amplitude (+/- fraction of radius_ref)
eoffset-per-angle.N.fmult float in (default: 6)
Offset frequency multiplier
eoffset-per-angle.N.k u32 in (default: 10000)
Scaling Factor (if 0, use 10000)
eoffset-per-angle.N.is-off bit out
invert is_on (for convenience)
eoffset-per-angle.N.enable-out bit out
To: axis.L.eoffset-enable
eoffset-per-angle.N.clear bit out
To: axis.L.eoffset-clear
eoffset-per-angle.N.kcounts s32 out
To: axis.L.eoffset-counts
eoffset-per-angle.N.kreciprocal float out
To: axis.L.eoffset-scale (1/k)
eoffset-per-angle.N.eoffset-dbg float out
offset (debug pin--use kcounts & kreciprocal)
eoffset-per-angle.N.state-dbg u32 out
state (debug pin)
GPL